Browsing by Author "Seabra, L."
Now showing 1 - 4 of 4
Results Per Page
Sort Options
- Beam tests of an integrated prototype of the ATLAS Forward Proton detectorPublication . ATLAS collaboration (27 authors); Seabra, L.The ATLAS Forward Proton (AFP) detector is intended to measure protons scattered at small angles from the ATLAS interaction point. To this end, a combination of 3D Silicon pixel tracking modules and Quartz-Cherenkov time-of-flight (ToF) detectors is installed 210 m away from the interaction point at both sides of ATLAS. Beam tests with an AFP prototype detector combining tracking and timing sub-detectors and a common readout have been performed at the CERN-SPS test-beam facility in November 2014 and September 2015 to complete the system integration and to study the detector performance. The successful tracking-timing integration was demonstrated. Good tracker hit efficiencies above 99.9% at a sensor tilt of 14°, as foreseen for AFP, were observed. Spatial resolutions in the short pixel direction with 50 μm pitch of 5.5 ± 0.5 μm per pixel plane and of 2.8 ± 0.5 μm for the full four-plane tracker at 14° were found, largely surpassing the AFP requirement of 10 μm. The timing detector showed also good hit efficiencies above 99%, and a full-system time resolution of 35±6 ps was found for the ToF prototype detector with two Quartz bars in-line (half the final AFP size) without dedicated optimisation, fulfilling the requirements for initial low-luminosity AFP runs.
- The ALFA Roman Pot Detectors of ATLASPublication . Abdel Khalek, S. et al. (46 authors); Conde Muíño, P.; Gurriana, L.; Maio, A.; Maneira, M.J.P.; Palma, A.; Seabra, L.; Wemans, A.The ATLAS Roman Pot system is designed to determine the total proton-proton cross section as well as the luminosity at the Large Hadron Collider (LHC) by measuring elastic proton scattering at very small angles. The system is made of four Roman Pot stations, located in the LHC tunnel in a distance of about 240 m at both sides of the ATLAS interaction point. Each station is equipped with tracking detectors, inserted in Roman Pots which approach the LHC beams vertically. The tracking detectors consist of multi-layer scintillating fibre structures read out by Multi-Anode-Photo-Multipliers.
- The calibration system for the photomultiplier array of the SNO+ experimentPublication . SNO+ collaboration (23 authors); Alves, R.; Andringa, S.; Carvalho, J.; Chauhan, D.; Gurriana, L.; Maio, A.; Maneira, J.; Seabra, L.A light injection system using LEDs and optical fibres was designed for the calibration and monitoring of the photomultiplier array of the SNO+ experiment at SNOLAB. Large volume, non-segmented, low-background detectors for rare event physics, such as the multi-purpose SNO+ experiment, need a calibration system that allow an accurate and regular measurement of the performance parameters of their photomultiplier arrays, while minimising the risk of radioactivity ingress. The design implemented for SNO+ uses a set of optical fibres to inject light pulses from external LEDs into the detector. The design, fabrication and installation of this light injection system, as well as the first commissioning tests, are described in this paper. Monte Carlo simulations were compared with the commissioning test results, confirming that the system meets the performance requirements.
- The LED and fiber based calibration system for the photomultiplier array of SNO+Publication . SNO+ collaboration (22 authors); Seabra, L.; Alves, R.; Andringa, S.; Carvalho, J.; Gurriana, L.; Maio, A.; Maneira, J.A new external LED/fiber light injection calibration system was designed for the calibration and monitoring of the photomultiplier array of the SNO+ experiment at SNOLAB. The goal of the calibration system is to allow an accurate and regular measurement of the photomultiplier array's performance, while minimizing the risk of radioactivity ingress. The choice in SNO+ was to use a set of optical fiber cables to convey into the detector the light pulses produced by external LEDs. The quality control was carried out using a modified test bench that was used in QC of optical fibers for TileCal/ATLAS. The optical fibers were characterized for transmission, timing and angular dispersions. This article describes the setups used for the characterization and quality control of the system based on LEDs and optical fibers and their results.